Montigo L-Series DF-ST Guia de Instalação descarregar pdf (Página 8)

Page 8

L-Series DF-ST See-thru Gas Fireplace

Part No. XG0812

f i r e f e a t u r e

Side Vent Venting Requirements

L38DF-ST

If your installation requires more than 12" of horizontal venting, some

vertical lift is required. Use the vent graph below to determine an

acceptable vent run. Unacceptable venting can affect the replace's

performance.

 the maximum horizontal vent run is 16 feet

The Venting Graph

Measure the vertical height from the replace hearth to the centre of

the termination and the horizontal run from the from the replace ue

collar to the wall ange of the termination. Plot on the Venting Graph

(Fig. 6) with an 'X'.

If the 'X' falls on or above the top boundary of the shaded area, the

installation is acceptable.

Example A: (Acceptable Installation)

If the vertical dimension from the hearth is 82", and the hori-

zontal run to the wall ange of the vent termination is 156", this

would be an acceptable installation.

Example B: (Acceptable Installation)

If the vertical dimension from the hearth is 72" and the horizontal

run to the wall ﬂange of the vent termination is 36", this would be

an acceptable installation.

Example C: (Unacceptable Installation)

If the vertical dimension from the ﬂoor of the ﬁreplace is 48" and

the horizontal run to the wall ﬂange of the vent termination is

108", this would NOT be an acceptable installation.

Short Congurations:

For installations straight through the wall, use an PTO-3/-3F termina-

tion and PXT-5 or PXT-10 to achieve the desired length. The maxi-

mum horizontal vent run with no vertical lift is 12". See Figure 7.

Figure 13a. L38DF -ST Side Vent Venting Graph

L38DF-ST

L42DF-ST

Example A: (Acceptable Installation)

If the vertical dimension from the hearth is 82", and the hori-

zontal run to the wall ange of the vent termination is 156", this

would be an acceptable installation.

Example B: (Acceptable Installation)

If the vertical dimension from the hearth is 72" and the horizontal

run to the wall ﬂange of the vent termination is 36", this would be

an acceptable installation.

Example C: (Unacceptable Installation)

If the vertical dimension from the ﬂoor of the ﬁreplace is 48" and

the horizontal run to the wall ﬂange of the vent termination is

108", this would NOT be an acceptable installation.

Figure 13a. L42DF -ST Side Vent Venting Graph

L42DF-ST

NOTES: All dimension lengths for vertical or horizontal runs are

measured from centre of the vent pipe.

Venting runs must fall within the limits set by the venting

graph (see Figure 9a).

Horizontal Vent Installation

Vent systems that terminate through a wall may comprise up to

seven different components:

A - Termination PTO-3

PTO-3F

B - Stucco Kits MSR (stucco frame)

MOSR (stucco can)

D - Flex sections PFL-1 (12" section)

PFL-2 (24" section)

PFL-3 (36" section)

PFL-4 (48" section)

E - Rigid sections PEXT-1 (12" section)

PEXT-2 (24" section)

PEXT-3 (36" section)

PEXT-4 (48" section)

F - Extensions PXT- 5 (5" section)

PXT-10 (10" section)

G - 90° elbow PEL-90F/F

PEL-90M/M

H - Heat Shield RHS101 ( for 5"/8" venting)

I - Heat Shield RHS 8 (for Top Venting)

Installation

26 1/2

27 1/2

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 21 22

Comentários a estes Manuais

Sem comentários

Montigo L-Series DF-ST Guia de Instalação Página 8

Comentários a estes Manuais

Manuais e produtos relacionados com Lareiras Montigo L-Series DF-ST